Never Miss a Deal.

I'm a professional drywaller by trade, and these are identical to the ones I see the electricians using all the time. They work great, and will work in pretty much any wallboard thickness from 1/4" up to 1" or even a bit more. One gripe is that due to the fact that the tabs which hold the unit in place are in alternate corners rather than in all four corners, the bracket will warp a bit when you tighten them down, and the coverplate will sometimes sit off the wall about 1/32" on one side or the other. The ones the pros use do the same, though. Finally, there should be a cutout template included with these. It's a pain to try to get the hole straight, level, and the right size without a template especially when trying to mount next to an existing device box, where any amount out of square will easily show.

PROS: Good build quality
Very secure once installed
Cheap
Simple to use

CONS: Monoprice NEEDS to put a cutout template in with these.
They don't sit 100% flat

I continue to convert any and all to Monoprice. That's why I really want everything to be perfect. But when I ordered a few different items, my three brackets were just thrown in the box. I had to throw one of them away because the tab broke. No big deal - it's $1.28 - but you know where I'm going with this.

PROS: Same product that Lowe's and Home Depot sells, but about $5 cheaper.

CONS: Packaging

For all the users who are having a hard time installing these, here is a video from the manufacturer on how to easily install them:

http://www.aifittings.com/products/videos.php?video_id=13

I purchased this bracket to use with the single gang low voltage wall plate (PID 3997). As for easy of use I would give the product a 10. After the hole was cut into the wall, it just slid in and with few turns of the screws and I had a neat looking secure bracket installed. The one deficiency would be the lack of a template for the hole. It took a little patience and guesswork to get the hole outlined properly but otherwise things worked out well.
The one caveat I will throw out there is for anyone wanting to use this with the single gang low voltage wall plate. When installed, the screw mechanism blocks the opening of the wall plate and cuts down the usable opening to about 2/3 the original size. Luckily I was only passing a few small speaker wires through so it wasn't a problem. But if you are planning on putting a power cord or other connectored cable through, I would recommend the 2-gang wall plate.

PROS: Easy to install

CONS: No cutout template
Screw mechanism gets in the way of the wall plate (PID 3997)

This part provides for a simple solution when completing in-wall wiring runs for Home Theatre installations. Each unit includes an effective clamping system that grips the drywall firmly while still providing a method for mounting monoprice's wall plate systems. Installation takes mere minutes providing a finished wire access solution. I found the related installation video from monoprice to be very helpful.

PROS: 1.) Ample screw lengths and binding cleats allow for fire-rated drywall thicknesses in excess of 1"
2.) The interior dimension can be uses as a template for cutting the necessary hole in the drywall.
3.) The cleat system is foolproof.
4.) Fit’s all monoprice single-gang wiring connector plates for Ethernet and other wire connectors.

It's nice to be able to pick these up with the rest of your order instead of having to make a separate trip to a big box store. Worked well for me adding Ethernet to all the rooms in my new home.

Would recommend pre-tightening the wings to just bigger than the thickness of your drywall before installing. The screws don't come all the way threaded through so it's easier to get a grip on them before shoving them in, and once the bracket is in place, it'll be a few quick turns of the screwdriver to get 'em snug.

PROS: sturdy, cheap, low profile, familiar

CONS: none

I like that I don"t have to cut off the back of a box to install a wall plate but like it more that i don't have to worry about how to screw a wall plate to the box. This bracket accepts a plate that lets the wire go into the wall without looking like an abyss, I order the bracket and plate too.

PROS: easy to use

CONS: price

Figured I would purchase this along with some other accessories I would use with it rather than go to the big box store to pick up an 'old work' box. Works great. Monoprice continues to impress with order accuracy, packaging quality, speed of service and competitive price.

PROS: Super simple to use

CONS: Absolutely none

Simple solution for mounting a face plate of your choice.

PROS: Works as designed.

CONS: Can't think of any.

Great design easy to install and remove if needed. Definitely what you need when running hdmi cables in wall and with the use of something like the recested low voltage wall plate.

PROS: Easy installation, good quality of materials, very inexpensive

CONS: None

This is a good solution for mounting low voltage wall plates. Installation is slightly harder than it needs to be though. It could be improved with a template to trace onto the wall the correct size of the hole you need to cut into the drywall (and one that you could level). As is, installation can be annoying trying to figure out exactly which part of the hole needs to be shaved to get the bracket to fit.

PROS: Good solution for mounting low voltage wall plates

CONS: Could be improved with a template to trace onto the wall the correct size of the hole you need to cut into the drywall (and one that you could level). As is, installation can be annoying trying to figure out exactly which part of the hole needs to be shaved to get the bracket to fit.

Good quality item. Really tightens well to the drywall, makes mounting the wall plate solid.

CONS: None.

Great price, easy to install, and does what it was designed to do!

These are awesome, so much better than the ones that I bought from the home improvement stores first. Once you've carefully cut the hole with a drywall saw, installing these are easy, they attach themselves solidly, and they even look professional before you put the plate on top of them. I bought more than I needed so I had some for the next room I'm going to work on.

PROS: Easy to install, looks good, attach to the wall more solidly than the flimsy metal tab ones you buy at the big stores, sit more flush than the plastic screw-on ones my electrician installed.

Website even has links to view video of installing most things. Thank you.

PROS: Quality product, cheap price. Dresses up nicely.

These are great for low voltage installs. I like how the anchor is in the top more so in the middle. This prevents bowing on the edges. Something from the hardware store will have the anchors on the edges that all the corners to pop up when screwing on a cover plate.

Good product. Easy to Instal. Holds up well against the wall. Just ensure you cut the drywall to the right size to give some strength to the holding bracket.

Works beautifully - used them to do some re-wiring in the living room's sound system. Ordered a handful, and glad I did - had to use one of these to replace the construction box in the wall before me had broke when I was taking off the old faceplate. Installed PID:3326 using one of these, as well as a coax wallplate I bought from Target.

PROS: Fits standard wallplates as well - not just Monoprice plates. open back makes for routing wires and cables MUCH easier than a construction box.

CONS: No template - have to use a level, measurements, checking, repeat or else worry about cutting too much of the drywall away and leaving a large hole in the wall. May want to use a drywall saw or a large (3") sharp pocket-knife to cut the hole.

These are absolutely great for low voltage wiring, and simple to install. Simply cut a rectangular hole and insert, then screw the little wings tight. These are great on walls with really tight spaces behind, too, since they can easily be cut to protrude as little as 1cm or so behind the wall.



They are a bit flimsy so don't try to force them too much.

PROS: Minimal, effective design.

CONS: You need to make your own cutout template (one-time task).

Used in conjunction with 3997 for professional through wall cabling.

PROS: High quality, easy to install, works as designed.

These worked great to hold my speaker connection wall plates.

PROS: Great price, Does exactly what it is supposed to.

CONS: None

Works Great and does exactly what its supposed to do.

The brackets are easy to mount into existing drywall, and work perfectly.

Simple low voltage bracket, the plastic ones are a lot more easy to work with than the metal. If you are ordering some other stuff and all ready need to pay shipping you might as well pick them up hear as there are slightly cheaper then others sell them.

Fits in properly cut hole (use a pencil to trace the inside and a drywall saw to carefully expand the hole as needed). Mounted perfectly and allowed proper placement of a keystone wall plate on it.

PROS: No sharp pokes from the screws and fits snugly when tightened. Aligns great with keystone wall plate. What more can you ask for?

CONS: none

Great Item. Have used hundreds of them for voice and data installations. As well as Audio, CCTV Camera Cables and Video (HDMI, RCA etc..).

PROS: These brackets are way better than using the metal cut-out rings that you squeeze onto the drywall and then screw-in, sometimes yo end up screwing into your finger while holding the tab in place inorder for the screw to align with the hole.

CONS: None

Works very simple and effective. Cut the opening by tracing the INSIDE of the bracket, pop in the bracket and tighten the screws. Botta bing botta boom.

PROS: Awesome

CONS: Not a thing

These are good little brackets and I have never had an issue with tabs bending even when using power drill and forgetting to dial back torque.
What is also a HUGE plus on this vs the home depot brand ones is that the threads are already cut into the tabs; these are easy while tightening down the home depot brackets manually is quite a chore.

Worked very well, and installation was simple. Would purchase again if needed for a future installation.

PROS: Perfect bracket for mounting HDMI wall plates to sheet rock.

CONS: None.

just what I needed. worked perfectly.

Good product, great price

Installed with (3997) and (3324) and Niles volume control

TIP:
Use a pencil, level, stud finder, and buzz cutter (to cut out hole for drywall).
Start by striking a horizontal line 10.25" above floor(this is for 12" center.. maybe different if your elec outlets are higher), then hold mount up to line and then make marks on each side on horizontal line, then use level to make vertical marks, then hold mount up and mark top, then use level to make top of your square, then use buzz cutter to cut out drywall (nice clean cut!).


PROS: Great value, works well!

CONS: They don't install themselves

I love these things! No hassle, no mess, just turn the driver a few times and you're done!

Wish these had been around when I was still at my previous job would have been a huge relief.

PROS: Works as advertised, and works very well!

CONS: Absolutely none.

good

PROS: Inexpensive
exactly what I needed
I wasn't able to find it anywhere else

Get a drywall saw and cut your wall hole, and you have a box in your wall so you can have a nice professional looking wall plate. Very cheap and easy professional looking solution.

PROS: Cheap, easy

CONS: None

great product at an awesome price

Not much to say its the simplest and most sturdy wallplate design I've used.

PROS: - Very simple design
- Inexpensive
- works perfectly

CONS: - None

These low voltage mounting brackets work perfectly. They feel and look exactly like the ones you get at a home improvement store, but they are cheaper priced. I have purchased multiple of these and they have all worked like a charm.

PROS: Fit like a glove.

CONS: None.

LOVE this product...i wonder how I would get my wall plates on the wall and this was the perfect solution.

Works fine. Good Price

Works great! Easy install, great price

We got exactly what we ordered and they worked great

Easy to install, super cheap price, great monoprice service.

PROS: Great price, great quality

CONS: None

Good quality, easy to use.

I am very happy with these brackets. I could only find cheap ugly brackets at the hardware store. These are easy to use and then fit with the face plate screws that I needed. My only regret is that I didnt order more at the time.

PROS: Easy install and easy mounting.

CONS: none

Great product. I've installed hundreds of these and will continue to use them as my go-to LV bracket.

PROS: Fastens very securely and easy to install

Easy install quality product no box or finding stud just tapped the wall and cut with razor knife

Works as described and makes the in home theater look good inside home

No complaints, works as expected.

When I tried cuting a hole for one new cable run, I discovered that behind the drywall, a 1/2" plywood backing had been used. I cut a hole through that and the bracket managed to still attach without a problem. I was happy they thought to include enough of a margin to handle 1"+ thick walls.

I was unhappy that the wall plate (Keystone plate) isn't flush with the wall because the bracket sticks out ~1/16" or so. More of a problem with the plate than the bracket, but it would have been ideal if it could be flush with the wall. No way to avoid that unless I dig out a small part of the wall for it to sit in. Now I have to use some caulk to fill it.

PROS: Easy to use, can be used with wider wall materials.

CONS: Sticks out from the drywallnot flush. Wall plate not flush with the wall.