Volume Pricing (Log In to see Member Pricing)
HDBaseT Wall Plate Receiver with Bidirectional IR Repeater, 100m (328ft)
Monoprice is a proud member of the HDBaseT Alliance
Add another receiver to your HDBaseT™ installation with this HDBaseT Wall Receiver from Monoprice!
This HDBaseT Receiver is designed to convert an HDBaseT signal sent from an HDBaseT transmitter over Cat6 cable into an HDMI® signal for use with an HDTV. It allows for a full bandwidth 10.2Gbps data throughput, which means that it supports all High Speed HDMI functions, including all HDMI 3D video modes, the extended 4K cinema resolution, 32-bit Deep Color, and high-definition compressed lossless audio, such as DTS-HD Master Audio™ and Dolby TrueHD™.
The Wall Receiver includes support for bidirectional Infrared (IR) Remote Control repeating. Additionally, it has two RJ45 LAN jacks for extending your local area network coverage. As long as the network is connected to the RJ45 jacks on the HDBaseT transmitting device or on this receiver, the network connection will be propagated throughout the HDBaseT system.
- Extends HDMI signals up to 328 feet (100 meters) using a single Cat6 cable
- Extends 100Base-TX network connectivity along with the HDMI video
- Can be daisy chained up to six units deep
- Built-in bidirectional IR repeater
- Supports all High Speed HDMI functions, including 3D video
This HDBaseT device is fully compatible with these other HDBaseT extender products from Monoprice:
- PID 10224 HDBaseT Wall Plate Extender
- PID 10225 HDBaseT Extender
- PID 10226 HDBaseT 4x2 HDMI Matrix Switch
- PID 10227 HDBaseT Receiver
Note: Monoprice strongly recommends using 22AWG, 24AWG, or active HDMI cables with Redmere technology to achieve the best results and to ensure minimum signal loss over longer distances.
|Supported Video||High Speed HDMI® with HDCP 1.2|
|Supported Resolutions||1080p, 1080i, 720p, 576p, 576i, 480p, 480i|
|Color Support||up to 12-bit/channel Deep Color (36-bit total)|
|Audio Support||LPCM, Dolby AC3, DTS® 7.1, DSD|
|Bandwidth/Data Throughput||up to 10.2Gbps|
|Operating Temperature Range||+5 ~ +131°F (-15 ~ +55°C)|
|Operating Humidity Range||5 ~ 90% RH (no condensation)|
HDBaseT™ and the HDBaseT Alliance logo are trademarks of the HDBaseT Alliance.
HDMI®, the HDMI Logo, and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries.
DTS® is a registered trademark and the DTS logos, Symbol, DTS-HD™, and DTS-HD Master Audio™ are trademarks of DTS, Inc.
Dolby® and the double-D symbol are registered trademarks of Dolby Laboratories. Dolby TrueHD™ is a trademark of Dolby Laboratories.
Second order (RMA) - 10/5/2015 lasted till 3/3/2016
I've had two sets of HDbaseT product from monoprice. They perform excellent. However, This is my second unit to go out in under 1 year. Each product lasted just over 5 months. I'm very hopeful it's just a bad power supply. Have ordered a replacement from amazon. Very hopeful replacing the power supply will fix the issue. As a long time customer I expect a higher quality from monoprice.
PROS: - Inexpensive
- Easy to use
CONS: - The Ethernet port on the back is near the edge and makes it very difficult to get a shielded CAT-6A cable connected when installing in a standard electrical box
- Only lasted thirteen months
PROS: Potential to work over long cable runs
CONS: Poor reliability. Need for separate power source. Complicated troubleshooting, especially for a cable that may by hidden and poorly accessible.
PROS: Cost-effective for HDBaseT,
CONS: Short lifespan,
IR can't be used with 1/8" minijack from control system or to a device - must use the blasters that come with the product
Blasters don't stick to cover an IR port, but must be placed nearby
Blasters are large and ugly when placed near or on TVs (ugly)
PROS: Simple to get up and running. Works as advertised. Good finish and appearance
CONS: Can't fault this end of the pair. The IR cable length issue at the tx end isn't a problem here.
PROS: * Reasonable price
* Ethernet ports for other devices
* Status LEDs
CONS: * External power required
* Silver color
* Only 100 Mbits
PROS: Works for Avatar 3D Blu-Ray
CONS: Wall plate did not come with the screws to attach to mounting box, which I found strange, but when I checked with Monoprice they verified it doesn't come with screws. I had to buy these screws on Amazon http://www.amazon.com/gp/product/B00368CEZ2/ref=oh_details_o06_s00_i00?ie=UTF8&psc=1. If you don't have screws it still works because it fits pretty snugly into the box, but I'm subtracting one star anyway.
Other reviewers have said that the power supply goes bad after a few months. I can't comment on that since I received the unit yesterday. However, I will say that the USB chargers and other power supply items I've purchased from monoprice have been sub par. (TV mounts, cables, and even guitar have been great.) Apparently you can buy a replacement power supply from amazon that is better quality.
This receiver works in my setup, long term results pending.
Yamaha RX-V675 with BluRay, Xbox360, Wii (upconverted by receiver), and Uverse (Motorola)
Receiver HDMI out to a powered HDMI splitter (over High Speed HDMI cable)
standard speed HDMI cable from splitter output to TV
HDMI High speed cable from powered splitter to HdbaseT extender (PID 10680)
100' 24AWG cat 6A STP to this HDBaseT receiver
4' high speed HDMI cable to BenQ 1070.
There is a slight blackout if I turn the TV or projector on/off while watching the other unit. Assuming this has to do with renegotiating the handshake. Signal did return in a few seconds with each test as expected.
Good luck, we are all in this together.
PROS: Passes a 1080i signal consistently where 75' HDMI cable (PID 6062 with booster) would not.
Not dropouts from Yamaha RX-V675 with BluRay, Xbox360, Wii (upconverted by receiver), and Uverse (Motorola).
CONS: Cat 6a output on side doesn't fit into a standard 2 gang low voltage box. You'll need to buy a 3 gang box and add a blank or notch out the side of the box.