Premium 3D Printer Filament ABS 1.75MM 1kg/spool, Black
    Product # 10545
    Premium 3D Printer Filament ABS 1.75MM 1kg/spool, Black
    Product # 10545
    In Stock This item will ship on 6/27/2016 if ordered within 2 days 15 hours 51 minutes

    Volume Pricing (Log In to see Member Pricing)

    Volume Pricing

    Qty: 1 $19.99
    Qty: 2-9 $19.75
    Qty: 10-19 $19.50
    Qty: 20-49 $19.25
    Qty: 50+ $18.99

    To see and take advantage of our member pricing sign up for a business account or contact our sales team.

    Learn more about Monoprice Business

    Premium 3D Printer Filament ABS 1.75MM 1kg/spool, Black

    Get outstanding 3D printing results when you use 1.75mm ABS 3D Printer Filament from Monoprice!

    ABS is one of the most commonly used filament types in 3D printing. It has a high tensile strength and good overall toughness. It has a low density and is softer than PLA, which means lower weight and lower cost when printing large models. Hardness is such that no white dot appears when bending.

    This 1 Kg spool features a thickness of 1.75mm ±0.10mm, with a roundness variation of only 0.05mm. It has a nominal processing temperature of 230° C (446°F). Thickness and roundness factors are laser measured at the factory to ensure accuracy over the entire length of the filament.

    The negatives of using ABS is that it can give off a white smoke with a concentrated odor. It is best to ensure that the printing room is well ventilated when using ABS.

    Additionally, it has a high moisture absorption rate. Depending on the overall humidity level of the printing environment, an opened spool can absorb enough moisture after a couple of days that high temperature printing could cause bubbles or pocks in the extrusion. It is therefore recommended to not open a spool until you are ready to print and to store any unused portion with with silca gel and/or an active dehumidifier to reduce the amount of moisture it can absorb.

    Reel Dimensions:

    • Reel Diameter: 195mm (7.68")
    • Hub Diameter: 95mm (3.74")
    • Spindle Diameter: 38mm (1.50")
    • Reel Width: 80mm (3.15")

    Related Categories

    8 Reviews

    63.75% of the reviewers recommend this product


    Inconsistant feed mid spool

    • Anonymous,
    •  OLD BRIDGE, NJ 
    • 10/14/2014 7:57:33 AM

    Pros: The filament will stick well on a heated glass bed between 115 and 120, extrudes well between 210 and 220.

    Cons: I am mid spool with this product and have had nothing but jammed feeds do to inconsistant diameter of filament and media wrapped so tight on the roll that it will not release caosing me to have to brake down the extruder and clean the feed mechanism. wasted a lot of time and filament with this batch of product. The other minor quirk is it is not as black as PLA and turns an ashen black when extruded.

    Unfortunately the price of a single spool has gone up after the release of the Monoprice 3D printer. This product at best is a three star because I was able to get half of the spool to extrude with minimal problems. No joy in losing a print and jamming up the extruder feed.

    Was this review helpful to you?

    No complaints

    • Michael Hannau,
    •  Bristol, CT 
    • 10/7/2014 5:45:16 PM

    Pros: Good price, vacuum packed, good prints.

    Cons: None so far.

    I have had good success with Monoprice for other products so I gave the ABS Filament a try.
    No problems with ordering or delivery and the product arrives vacuum sealed. I have used this filament now for 5 print runs of 4"x4"x1" items on my Solidoodle 2 with no issues.

    Was this review helpful to you?

    Monoprice Filament in several colors

    • Anonymous,
    •  Baytown, TX 
    • 8/15/2014 8:18:29 AM

    Pros: Cheap
    Good spool especially like the filament keeper holes
    Generally Good quality
    Low melt point

    Cons: Inconsistent Quality
    Doesn't react to acetone as strongly as other filament brands

    I've had several spools of Monoprice ABS filament at this point. White(x2), Black(x2), Red, Fluorescent Green, Fluorescent Yellow

    For the most part the the filament has been good. I had some white that was spectacular and I could not make a bad print.

    The black... same way until halfway through I got a clog. Cleaned the nozzel(torch) and start up only to clog again a few prints later. Replaced the extruder and moved up to an E3D and sure enough clogged that one too!. So I tossed the last 1/3rd of that roll.

    The green... worked like a champ after I dialed it in.

    Red ... has not been very good. I cannot seem to find the right temperature to print this filament at.

    The yellow... worked great until I left it out for a week. I went back to print and started getting pops. It had absorbed to much moisture. I don't think this is the fault of the filament but I've left other brands on my printer for a week (only printing on the weekend) and not had this issue.

    Got another roll of Black and it prints really good but is brittle. If I put to much strain on the spool it bends the filament easily. Overall though it's printed pretty good when I can keep it from bending.

    Overall I like the filament from Monoprice and I would say that 70% of the time I get excellent prints. I will continue to use their filament especially the white.

    Was this review helpful to you?


    • Anonymous,
    •  San Jose, CA 
    • 6/13/2014 7:34:33 PM

    Pros: Fast shipping??

    Cons: Brittle
    Poor layer adhesion
    Often clogs up extruder - impure?

    Bought this because I ran out of black filament and needed it fast: I've had good experiences with Monoprice's red PLA and the reviews on the black ABS weren't bad.

    But the ABS ( if it's even ABS ) that came is basically unusable.... it's brittle, doesn't stick well, and constantly clogs up the extruder on my Makerbot I can't finish a print any longer than 10 minutes... I've used plenty of brands of filament but nothing's ever been this bad.

    My roll's probably just defective, but basically just wasted $35...

    by Monoprice Administrator

    Thank you for your review. And I am truly sorry to hear of your experience you have had with this product. For now, if you prefer, I can assist you in setting you up for a replacement on the item if you haven't done so already. We do have a lifetime warranty on cables as well as a 1 year warranty for everything else. It will be of no additional cost to obtain a replacement, so please let me know if you want to continue. I would just require your order# to set it up. Thank you!

    John Lingo
    Tech Support
    Was this review helpful to you?

    Quality ABS filiment!

    • Matthew Lovell,
    •  San Bernardino, CA 
    • 6/13/2014 9:31:15 AM

    Pros: Price
    Availability of colors
    Speed of Delivery!

    Cons: none so far

    Filiment works flawlessly in Afinia H series printer. smooth clean prints with no issues.

    Was this review helpful to you?
    Tax and shipping will be calculated at checkout