Volume Pricing (Log In to see Member Pricing)
1000FT Cat 6 Bulk Bare Copper Ethernet Network Cable UTP, Solid, In-Wall Rated, 550MHz, 24AWG - Black
4x4 Matrix HDMI® Switch & Splitter over CAT5e/CAT6 Cable w/ Remote - Extend Upto 131ft
If you've got a sports bar or restaurant and you want to show different programs on different TVs, or if you've got a house full of kids and family, each of whom wants to watch their own shows, you need an HDMI® Matrix!
This 4x4 Matrix HDMI Switch & Splitter is the perfect way to get ultimate flexibility out of your entertainment system. You can plug up to four different HDMI sources (e.g., blu-ray player, DVR, Xbox 360, PS3, etc.) into the Matrix and up to four output displays. The Matrix will let you independently switch between the four inputs for each display. Each display can simultaneously use the same signal or any combination of different signals.
Unlike most Matrix Switch/Splitters, this model also includes the capability of extending either or both outputs over a pair of Cat5e/Cat6 cables up to 40 meters (131 feet) away! This lets you deliver full 1080p signals further than you could with HDMI cable alone (about 25 feet) and saves you money by using cheaper Cat5e/Cat6 cable for the longer distance delivery.
The kit comes with five remote controls, including a main remote for controlling the Matrix directly, and four smaller remotes for controlling it from the rooms where the Cat5e/Cat6 receivers are located. Additionally, it comes with infrared repeaters, allowing you to control your source devices from the remote location(s). As a bonus, the receivers and/or matrix unit can be controlled with a computer using the RS232 interface.
In addition to the Matrix's own remote controls, each receiver unit can receive the remote control signals from the remotes for your various source devices (blu-ray player, cable box, etc.). These IR signals are then transmitted back down the Cat5e/Cat6 cables to the main Matrix unit, which then distributes the IR signal to an IR emitter that corresponds to the source device feeding the signal to that receiver. This allows you to use identical source devices with identical remote control codes, yet still independently control each from the remote location, providing the emitters and devices are not positioned so that one can "see" the IR signal intended for the other.
- View any of up to 4 sources on any of up to 4 displays
- Supports High Speed 1080p video
- Supports 3D
- Supports HDCP
- Connect either or both displays directly, using HDMI cable, or up to 40 meters (131 feet) distant, using Cat5e/Cat6 cable and included receivers
- Supports 225 MHz/2.25 Gbps per channel (6.75 Gbps all channel) bandwidth
- Supports 12-bit per channel (36-bit all channel) deep color
- Supports uncompressed audio such as LPCM
- Supports compressed audio such as DTS® Digital, Dolby® Digital, DTS-HD Master Audio™, and Dolby TrueHD™
- Includes five remote controls to select input devices for each output (one main remote for both outputs and four individual remotes for each output)
- Select inputs using included remote controls, with switch on front of matrix, with switch on front of receivers, or with a computer using RS232 input
- Includes infrared emitters to control source devices through remote receivers
- Gold-plated HDMI connectors
- CE, FCC, UL (Canadian and US), and RoHS compliant
Note: Monoprice strongly recommends the use of minimum 24 AWG HDMI cables when connecting a device, such as this matrix, between the source and destination devices to ensure minimal signal loss and maximum High Speed signal reliability.
For best results, use Cat6 STP cable whenever possible, especially for longer runs.
HDMI, the HDMI Logo, and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries.
PlayStation and PlayStation 3 are trademarks or registered trademarks of Sony Corporation.
DTS is a registered trademark and the DTS logos, Symbol, DTS-HD and DTS-HD Master Audio are trademarks of DTS, Inc.
Dolby and the double-D symbol are registered trademarks of Dolby Laboratories.
Microsoft, Xbox, Xbox 360, Xbox LIVE, and the Xbox logos are trademarks of the Microsoft group of companies.
|Input DDC Signal||5 volts p-p (TTL)|
|Output Video||HDMI® with HDCP, directly or via UTP|
|Video Amplifier Bandwidth||225 MHz / 2.25 Gbps|
|Vertical Frequency Range||50/60 Hz|
|Supported Resolutions||480i (SD), 480p, 576i, 576p, 720p, 1080i, 1080p|
|External Power Supplies||5 VDC, 2A|
|Matrix Power Consumption||8W|
|Receiver Power Consumption||5W|
|Operating Temperature Range||0°C to +70°C|
|Operating Humidity Range||10% to 85% RH (no condensation)|
|Storage Temperature Range||-10°C to +80°C|
|Storage Humidity Range||5% to 90% RH (no condensation)|
|Matrix Dimensions||17 11/32" wide, 8 3/16" deep, 2 1/16" high|
|Receiver Dimensions||6 1/16" wide, 2 3/4" deep, 1" high|
|Matrix Weight||2218 gm|
|Regulatory Compliance||FCC, CE, RoHS, UL|
Included in the Box:
- 1x 4x4 Matrix Switch & Splitter
- 4x Cat 5e/6 Receivers
- 4x 2A AC Adapter with 44" cord
- 1x 5A AC Adapter with 42" cord
- 4x IE infrared emitters with 48" cable
- 1x IR infrared receiver with 49" cable
- 4x HDMI® Switch remote control with installed CR2025 battery
- 1x HDMI® Matrix remote control with installed CR2025 battery
- 1x User manual
Please remove plastic tab from remote control battery compartment before use.
HDMI, the HDMI Logo, and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries.
Questions and Answers
Feel free to reach out to our technical support team should you require additional assistance!
I've grown pretty dependent on this switch for my household video distribution. I feel very appreciative of the other more technical reviewers here that indicated that when this devices fails, its usually the power supply. In my case the device flashed blue on all LED's at startup. The other gracious reviewers indicated this was also another indication of a failed power supply. Not wanting to spend another $300 on this device or at least $1500 for a higher grade device I searched around this 5V 6a power supply and paid $26 +shipping. Powerstream provides the the option of buying a barrel connector adapter kit but its not necessary the base connector fits just fine in the switch. The switch is now functional. I hope this helps!
PROS: Its cheap. It works great when its working. I have been happy with it for 23 months.
CONS: It stopped working at 23 months. As the other reviewers have advised, it has a shorter lifetime than you would hope for.
PROS: Dirt cheap, works as advertised. 4 x 4 matrix solution for your entire house.
I have been a user of this for 4 years now, I paid much more from a different vendor. And at the 3x the price, still was cheaper than most solutions in 2008.
CONS: I have had the power supply fail 3 times on me. I suspect my longest run, which is used the most, taxes the device. (on easily 12 hours a day....)
I found a power supply that comes very close to matching the odd output voltage. May void warrantee if used. However, this one lasted me 3 years before failing. I just ordered more. Search web for part 91-56394. ouput volt is 5V & 4A on spec. (vs 5.5v & 4a from manufacturer)
So after all the wiring was run, I purchased a 4X4 HDMI switcher and four of the HDMI to Cat 5e/6 converters from Monoprice. I had no end of troubles with this setup! Ripping my hair out and trying a wire array of scenarios, I couldn't get any consistency. Sometimes the TV would work upstairs, sometime it would read "not supported". When the kids would turn on the bathroom light on the other side of the house, the bigscreen would drop the signal like there was a voltage drop.
I was about ready to suck it up and return everything and leave the useless wiring in the walls...
BUT... Then this device came onto the market. I checked the website 5 times a day to see when it would be available thinking the automatic notification wouldn't work (my luck with tech)... And finally, I got it ordered!!!
It arrived in the mail, I unboxed it and hooked it all up. Spliced some Cat6 cables that were already terminated and hooked the stuff up...
and VOILA!!!!! It worked! But I knew not to get too excited because the last one worked too for the first 10 minutes before the HDMI handshake or the kids went to the bathroom.
But it's now been a week and EVERYTHING is working flawlessly! PS3, HDPVR, HTPC connected to a 55" Philips LCS and a 32" Sharp Aquos. No handshake issues, remote extender works perfectly.
I am so happy. This has been a nagging factor and the WAF (wife acceptance factor) did NOT like it when the tv would flicker or she'd need to reset everything because of a handshake...
This thing just WORKS!!!
CONS: - Sometimes, the activation light stay active with an input, even if the source unit is off.
- LED's are a little bright for a dark room when watching a movie or going to sleep.
- Remote receiver of the HDMI receiver seems a little weak over 15 feet for the IR.
That being said after a 2 year ordeal, I'm giving up on the monoprice 4x4 HDMI extenders. I tried 2 of the PID 5704 which worked great for about 6-8 months or so each. When I wrote in to chat on the second bad 5704 I was told by tech support that my setup was "unsupported". When I bought the unit and all the cables it didn't seem to be a concern. But, I was told that I needed to upgrade to the 8151 to get the distances I need. I paid more money to get the "upgraded" unit and even bought 2 100ft Cat6 STP cables to replace a 100ft monoprice HDMI cable. (I kept my 131' monoprice hdmi cable in place as it is much harder to re-run.
The 8151 worked great out of the box and I was hopeful that we had finally found something that worked. I mean double the price should get me higher quality stuff, right? Well, about 6 months later with nothing changed, it died. It wouldn't send any signals anywhere and would just blink all the blue lights on and off angrily at me whenever I pushed any of the buttons.
RMA dept was nice and sent another 8151 switch. I'm not sure but judging by the box, I think I got a refurb unit. I plugged it in the day I got it and only one of the outputs worked at all (even had some new blue lines that would show up sometimes). The other outputs would either get no signal or would cut in and out constantly. Those same outputs work fine when direct connected to equipment using the HDXT-E60 or with the 131' HDMI. I went through tech support gyrations of powering on and off everything and powering it on in a certain order. Then, trying the one output that worked with other outputs etc... This had no effect. I was very sad and tired from running around the house, up and down 2 stories multiple times.
Tech support chat then blamed the 28Awg HDMI cables from source to Switch and from the end-of-run reciever to the TV. I felt duped but I went ahead and shelled out another ~$60 to get these cables. I replaced the cables and was in the exact same situation. Tech support then says the 131ft monoprice HDMI cable I use for one of the runs is not supported! He referenced a badly worded sentence in the product description. I disagree about the "support" for this cable. It is a Monoprice cable that carries the HDMI logo. With that logo/standard no length min/max exist, only that if it carries the HDMI label, it's supposed to work. If this were the only output not working I would consider going through the hassle of replacing it. However, since the 131' cable works when directly plugged into equipment that I wouldn't even expect to be able to send that distance, I really believe this cable is not the issue and that the build quality of the switch itself is the problem. That and other, shorter runs well within the 131' advertised max are having issues, only when using this switch.
Rather than wait for this piece of equiptment to come back in stock, I'm going to order a different model, elsewhere.
Just for reference, my setup (all monoprice cables, professionally run):
2 x 35ft Cat6 UTP runs, 1 100ft Cat6 STP run, 1 131ft Monoprice HDMI cable run
Inputs: 1 Comcast Cable box, 1 Sony bluray player, 1 Media Center
Outputs: 1 LG LED TV, 1 LG Plasma TV, 1 Samsung LED TV, 1 Samsung Plasma
PROS: When it's working it's great!
Monoprice customer service doesn't seem to mind replacing them if they are in stock.
CONS: Doesn't seem to last. Tech support blames cabling, doesn't seem to have any testing capabilities of their own.
PROS: Great functionality, in some cases one of the best solutions, but unfortunately doesn't last long.
CONS: All units break right after the warranty expiration - flashing LED lights and no signal.
PROS: Worked pretty well for awhile. Had to turn it off and on a couple of times when the signal was bad.
CONS: Works for about 15-18 Months
PROS: Price is right. When they work, they work. They seem to be built to last about a year or so. Hmmm?
CONS: I am now on my second unit after the first stopped sending signals to all but one output. Orig. unit was out of warranty and customer support has very little sympathy. Known problems exist with this system but seem to have not been addressed through any updates or enhancements.
I am having problems with the IR system in the new unit from the day I installed the replacement system (1/8/15). Tech support continues to send me (fix-all) suggestions that have nothing to do with the actual problem. By the time they respond and give you their "boiler plate" fix-all suggestions, several days and weeks go by. Without the ability to control the inputs from any of the TV locations, the system makes a better paper weight than a piece of electronic equipment.
The description of this device should be modified to show that it requires dual Cat5/Cat6 cables to be run from the source location (4x4 Switch/Sender) to each TV location.
Had I known the first time around how the Switch/Sender should operate without cut outs between changing inputs, blue screens at random times, loud screeching signals with a black screen, etc., I would have made a replacement request consideration with the first unit during its warranty period.
I would request using a CC for purchase that adds an additional year of warranty to the purchase.
1.5 years ago I installed to the main room in a very large club a cobbled together 4 source matrix with monoprice components.
I used 3x 6532 (HDMI extenders over dual cat5/6) to drag one comcast & two DirecTV HD sources 100' into the main room. These sources along with a local VJ HDMI cable hit the inputs of 4 of the 6192 (1x4 HDMI splitters). Three outputs of these splitters fed 3 of the 5704 (4x4 HDMI matrix). These drove Large screen HD displays and full HDMI projectors...excepting that two of the matrix outs fed two more 6192 to mirror 4 displays each.
Monoprice tech service said I was on crack...might work...probably not. The club knew going in that it was a risk, but were fine with the experiment as it was so incredibly much cheaper than the known brand commercial systems and Monoprice has a great return policy.
It has worked with virtually no issues since install.
Flash-forward to current: The club decided to expand their matrix throughout the rest of the building & add displays.
I took the one remaining out from each 6192 source splitter & fed them to 4 of the 8160 (1x8 over single cat5/6 splitter & reciever set) each out was run to an input of an 8151 (4x4 matrix over dual cat5/6 with recievers) in one of the other rooms downstairs. One output from each 8160 ran upstairs to then feed one of 4 8159 (1x4 splitter over cat5/6 & reciever set). The 8159 outs fed inputs of 3 more 8151 matrices for the displays in the upstairs rooms.
Again Monoprice tech support was convinced that I had completely lost my mind.
We have a perfectly functioning 4x38 full HD matrix running as I type this & they'll try adding more displays later as the infrastructure has leftover matrix outs. The club is well aware that at any point the next display might be the straw that breaks it, but it is absolutely performing so far. Any source, any display, just like it should be.
1. Use heavy gauge very short HDMI cables. Copper is your friend. We predominately use 4963 and 4964 24ga 1' & 2' cables for connection between any boxes or converters. On the original install there wasn't a single cable under 24ga & any over 10' were heavier.
2. Use cat6 cable. Build your own. It's not much more at all by the spool than cat5 & it's less signal loss. Again, copper likes electrons and therefore you like copper.
3. Get a Lan cable tester & test cat6 cables when you build them, not after you have the whole rig together. Cables that don't work look suprisingly similar to ones that do without a tester.
4. If doing a larger install, order spare units with the first order. We had DOA: 1x 8160, 3x 8151, two of the switching supplies for the 6192. I have no fear that Monoprice will make it right when I call them next week, but since I was smart enough to order spares initially my customer install works now, on schedule.
PROS: system is compact and looks very sleek. Before I bought this I read the reviews from these other customers and some were complaining about the other TV's Flickering or do something when an input is changed. Seems to me they used cat5e, I used cat6 and did not come across any problems at all. Make sure to LABEL YOUR WIRES !!! I am an A/V guy so this comes naturally for me, but for guys trying to do it themselves... buy a darn sharpie it will make your life a lot easier especially if you do not have the right tools to help you locate wires.
CONS: Ir that comes with each device:
Too big, most IR emitters are sleek and out of plain sight. These things look like a mini mouse for my computer. They also do not have a mounting solution. I know double sided tape will work, but that is besides the point.
Once again does not come with a way to mount. I was forced to zip tie them to the arm of my articulating bracket. Yes it did work, what's going to happen when I am installing a flat bracket??? Should I toss it over... the answer is NO to all of you who are thinking i should.
I understand you guys are proud of your logo, but I do not want my customers to know where I bought this or any other product. They will cut me out of the mix
This system ultimately saves me $20 a month as I don't need two more directv boxes and don't need to buy bluray players for each room.
As I mentioned in my cons, it does downgrades the video/audio to the weakest link in your system, so don't expect to use a 1080p 7.1 source on a 720p LCD with stereo speakers and a 1080p projector with 7.1 receiver at the same time, as the signal will be downgraded to 720p and stereo for both. The best way to get around this is to do what I did and purchase inexpensive 1080p/7.1 capable receivers for each room you plan to use them in. I found a Yamaha model on sale at the egg for $130 shipped. So that allows me to have full 1080p/7.1 in each room, even while powering a 720p lcd because the Yamaha does the downscaling, not the input device.
This system just seems to work and I'd recommend it in a heartbeat. Monoprice got it to me quick and is half the price of other vendors who are selling the same model with a different name on the box.
PROS: - Seems to "just work", which is a great thing!
- Price, this is half the price of other vendors selling the same model, with a different name.
- Quality of picture is great, no difference that I can see using CAT6 versus hdmi.
- IR receivers are built into the receivers themselves, rather than dongles on other kits.
CONS: - IR emitters are standalone and don't attach to device, so create issues when trying to mount in a rack.
- Doesn't come with rack mounts, thought screw holes are there.
- Remotes are a bit cheap feeling, but for the price I don't see this as a real con really.
- Downgrades the audio/video to the lowest capable device hooked to switch. So if you have it hooked to an old HDMI tv, you'll only get 2 channel audio rather than 7.1 on any of the other inputs. This is really an HDMI limitation technically, but other matrix switches have over come this... but really, at the price, this is expected.