Chat Now
Vertical Adjusting Ceiling Bracket for Projector w/ 400 - 600mm Extension (Max 22Lbs) - BLACK
In Stock This item should ship today (11/27/2015) if ordered within 2 hours 50 minutes

Vertical Adjusting Ceiling Bracket for Projector w/ 400 - 600mm Extension (Max 22Lbs) - BLACK

This bracket allows you to mount your projector to a ceiling with an angle of up to 15 degrees.

This mount holds a projector from the top at a distance of 15.7" to 23.6"(400-600 mm) from the ceiling surface. It can accommodate projectors with a 3 or 4 mounting holes and a spacing diameter of 1.6" to 12.2" (40-310 mm) and a weight of up to 22 lbs (10 kg).

Provided the total diameter of the projectors wires/cables is less than the internal diameter of the vertical mounting bar they can be contained within the vertical bar for a neat and professional appearance. The projector can be tilted in both the horizontal and vertical axes, ±5 degrees horizontally and ±15 degrees vertically. Positioning screws allow precise control of the tilt angles, while locking screws keep it in the perfect position.

Included in the Box:

  • 1x MPCN-D4060 Projector mount assembly
  • 4x M6x25 tapping screw sets
  • 4x 6x50 wood screw
  • 2x M5x8 phillips screw
  • 6x M5x10 phillips screw
  • 4x M5x30 phillips screw
  • 4x M4x30 phillips screw
  • 4x M3x30 phillips screw

Projector not included!

Support Files:

4 Reviews

100% of the reviewers recommend this product


Could have used better instructions

  • Anonymous,
  •  Lawrenceville, GA 
  • 9/11/2014 2:37:42 PM

Pros: Sturdy. Great build quality, especially for the price!

Cons: Instructions are not the clearest.

The mount works great. For me, I only have 3 hole mount on my Optoma projector and they are close together. The instructions on how to configure it for my purposes were not clear at all. I was able to figure it out though. In the end I would recommend this mount, especially at such a low price. You may have to spend extra time though figuring out how to configure the arms for 3 hole configuration as well as close mount hole space configuration.

Was this review helpful to you?
  • Greg,
  •  Palm Harbor, FL 
  • 2/11/2013 6:52:00 AM

Pros: Solid, easy to install, great price!

Cons: None

Great mount. Very sturdy for such a long extension - no sway or sloppiness. Handsome look and of course great price!!

Was this review helpful to you?

Will not properly fit Epson 3020

  • Btech,
  •  Rogers, AR 
  • 11/21/2012 2:48:12 PM

Pros: Solid, better build than the less expensive Monoprice options

Cons: Doesn't fit the 4 holes in the Epson 3020 - just an inch short =(

The 8803 will work with three of the four arms hold the front center and two-left mounting holes, but not he four holes to make a centered square. Doing it with just the three will put it slightly off-center, but will work OK for my application.

Was this review helpful to you?

Nice product just as described

  • Happyuser,
  •  Plano, TX 
  • 8/3/2012 3:01:27 PM

Pros: Very good product worked fine for my installation came with all proper parts and very easy to install.

I loved the product. I was installing optomo gt 350 projector and it worked fine. Only issue was with the projector it's a 3 hole but was able to remove the extra arm and make it work. Order was delivered on time and is a good quality and workmenship on the product. Similar mounts will cost an arm and leg other places. I would buy from this site

Was this review helpful to you?
Tax and shipping will be calculated at checkout