Blade for Punch-Down Impact Tool 66 Type
    Product # 7045
    Blade for Punch-Down Impact Tool 66 Type
    Product # 7045
    $3.43
    Quantity:
    Out of Stock ETA: 8/26/2016

    Note:

    Due to limited supply, all products are sold on a first-come first-serve basis.  Auto Notification does not guarantee either availability or price. All prices are subject to change without notice.

    *Your information will only be used to notify you when this item becomes available. Carrier charges may apply for SMS text messages.

    Volume Pricing (Log In to see Member Pricing)

    Volume Pricing

    Qty: 1 $3.43
    Qty: 2-9 $3.30
    Qty: 10-19 $3.18
    Qty: 20-49 $3.06
    Qty: 50+ $2.94

    To see and take advantage of our member pricing sign up for a business account or contact our sales team.

    Learn more about Monoprice Business

    Blade for Punch-Down Impact Tool 66 Type

    This is a replacement blade for Punch-Down Impact tools.  It features dual 66 type tips.  One side has a built-in cutter.  The other side is the standard blade without the cutter.
     
    Compatible with punch down impact tools that feature sure-lock blade holders.

    10 Reviews

    49% of the reviewers recommend this product

    ADD YOUR REVIEW
    • Anonymous,
    •  Boise, ID 
    • 4/16/2015 11:01:54 AM

    Pros: it fits in my punch down tool and cuts the wire well.

    Cons: It gets stuck on the pins of the 66 block. I have to hold the 66 block and pull very hard to get the punch down tool off the pin.

    I hope I just got a defective blade. Maybe it did not get shaped properly. Great price. I could not find one cheaper than twenty dollars. I have to hold the 66 block and pull very hard to get the punch down tool off the pin.

    Was this review helpful to you?

    works

    • Aerilus,
    •  liberty, NC 
    • 2/11/2014 7:41:03 PM

    Pros:

    I don't know what was going on with others finding this blade to small to fit. I tested it on a few different blocks from different manufactures that were produced over the last 20 years and it fit fine on all of them. I rate is an upper mid-level fully functional product. the finish is a little rough but honestly who cares. it works.

    Was this review helpful to you?

    Great Punch-Down Blade

    • Soren Stoutner,
    •  Wickenburg, AZ 
    • 9/13/2013 3:41:19 PM

    This is a great punch-down blade.

    Was this review helpful to you?

    Still doesn't fit

    • Tripp,
    •  New Bern, NC 
    • 8/21/2013 1:56:45 PM

    Pros: It is cheap

    Cons: It doesn't fit a 66 terminal

    There are numerous reviews saying this blade won't fit a 66 block. Later followups seemed to indicate the issue was fixed. I took a chance and ordered one. They are still too small. I've already requested a RMA refund.


    by Monoprice Administrator
    Hello Tripp,

    Thank you for your review and my apologies for the issues you have experienced with PID 7045. A shame it didn't work out for your needs.. Ill be sure to pass this info along to our product team to further investigate the matter. Sorry again for the trouble and thanks for your support!

    Regards,
    Jonathan Arteaga
    Tech Support Associate
    ------------------------------------------------------------------
    Was this review helpful to you?

    Bit is too small

    • MVP,
    •  Indianapolis, IN 
    • 3/29/2013 11:57:20 AM

    Cons: I have two of these bits, and both are too small to fit over the terminal. The replacement bit is even smaller than the original.

    I discovered these bit problem comments after my defective bit arrived. This bit probelm has not been corrected. I pointed out that this is a known problem, but was blindly sent another useless bit. Insanity is doing the same thing over and over while expecting different results.


    by Monoprice Administrator
    Hi Larry,

    Sorry for the problems you are having with the punch down blade not fitting over the terminal properly. I have notified our Product Team of the issue so they can review and test out this blade. In the meantime if you like I can issue you an RMA for a return. I would just need an order number to get the process started. Again my apologies for any inconvenience this may have caused.

    Sincerely

    Tjayi Malone
    Tech Support
    Was this review helpful to you?
    SIGN UP FOR EMAIL DEALS
    SUBTotal
    Tax and shipping will be calculated at checkout
    MY CART