Chat Now
Surface Mount Box 2 port
In Stock This item will ship on 11/27/2015 if ordered within 21 hours 42 minutes

0.22 lbs

Flat Rate Shipping Prices

  • 0-3lbs- $4.99

Surface Mount Box 2 port

Versatile modular surface mount box for when in-wall box and wire installation are not possible. Use with keystones for the connector of your choice. A clean and simple solution for network expansion.

Box is durable plastic, white in color. With UL listing info printed in small blue letters on box face.
Comes with double sided adhesive mounting pad to mount the box to the wall, or you can use the two screws provided to screw it down to baseboard, window sill, trim, etc..
Jacks are not included. Use our keystone jacks with this box except PID# 5370-5377, 5394, 5398, 5399.
Comes with 2 zip ties to secure wires to box to prevent pull through.
Box has two slits in the back side to allow the wires to enter the box for flush moutning. Box top snaps on and off for easy access to wires.
NOTE:  NOT Compatible with PID# 5370-5377, 5394, 5398, 5399.

*Monoprice continually strives to improve its product line to bring our customers the best products available. Therefore, changes may be made to listed specifications without prior notice. Item received may not match photo or specs shown.

14 Reviews

92.86% of the reviewers recommend this product


Nice Surface Mount Box

  • Arthur,
  •  Woodside, NY 
  • 11/17/2015 7:40:22 AM

Pros: Easy to install, has an option to screw in the wall and screws included, with cable tie and it comes with double sided adhesive pad. This surface mount seems to work perfectly with Keystones jacks only but surprisingly it works with Leviton jacks too. A little extra push but it did work.

Cons: Once you close the cover its very hard to re-open. If you use the adhesive pads chances are you will removed it.
My suggestion is to use both screws and sure enough it will slow down your work. To compensate the work, use a power screw driver, with option that can be bend an angle for tight corners.

I like the surface mount color, size, installation kit, and functions.

Was this review helpful to you?

Perfect, don't change a thing

  • Anonymous,
  •  Plano, TX 
  • 4/30/2015 6:43:21 PM

Pros: Inexpensive
Perfect fit

These work great for Cat5/Cat6. The keystone snaps into a plate that slides into the surface mount. The cover snaps onto the base. You can mount with the double stick tape or the screws.

Was this review helpful to you?

Simply perfect

  • Daren Douglas,
  •  ,  
  • 12/5/2014 12:43:31 AM

Pros: Inexpensive and easy to install.

Cons: None that I could see.

These little boxes were awesome. I ran Cat6 all through my house and needed disconnects in the attic. My intent was to have all the solid wiring in and terminated at both the patch panel and all of the drops.
My problem was that I wanted to add several IP camera with the option of just throwing a jumper cable to connect it to the system.
These boxes fit the bill pefectly. The came with 2 screws to mount the base onto the joists and the keystone jacks fit perfectly.

Was this review helpful to you?
  • Anonymous,
  •  Vancouver, BC 
  • 7/30/2014 11:57:52 PM

Pros: Compact size with room inside to work comfortably.
No need to snap keystones in and out. Simply slid in, then snap the cover on.

Cons: No instructions on how/where to put the zip ties.

For those trying to figure it out, the zip ties go through the vertical slots on the bottom wire holders (near the exit) to hold the wires in place as strain relief.

Was this review helpful to you?


  • Dan Carp,
  •  Cambridge, MA 
  • 5/22/2014 6:52:07 AM

Pros: Cheap
Looks nice enough

Cons: A tiny bit fragile - plastic is thin

9 stars of 10 for the reasons above - definitely does the job, just a bit fragile

Was this review helpful to you?
Tax and shipping will be calculated at checkout